Secondary Pressure Regulation Range | 0 – 115 psi (8 Bar) |
Operating Pressure Range | 0 to 145 psi |
Regulator Range | 0 to 115 psi |
Porting | 10-32 (M5) |
Flow Rate | Dependent on regulator model. |
Media | All neutral liquid and gaseous media. Consult factory before use on liquids. |
Types | Non-Relieving. Single stage, diaphragm/spring construction |
Response Time | Dependent on secondary volume. Response average: 75 ms at 20% loss of secondary air pressure; 1 sec at 50% loss of secondary air pressure. |
Adjustment | Screw driver (or knob accessory) Equipped with locking nut to prevent tampering after setting is made |
Materials | Buna N Seals Brass Housing (Nickel Plated) Stainless Interior Parts Brass Interior Parts |
Operating Ambient | -10 to +60 ?C -14 to 140 ?F |
Height | 1 11/16 in. |
Width | 5/8 in. |
Weight | 2 oz. |
Drilling Plan | Mounts in 1/2″ dia. hole. Equipped with mounting nut. Behind panel depth – 1 1/8″. |
Item # 50880-00-80-10
Price Summary
- $98.34
- $98.34
- $98.34
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Weight | 0.19 lbs |
---|
Be the first to review “Item # 50880-00-80-10” Cancel reply
You must be logged in to post a review.
Related Products
Item # 50880-00-40-10
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Item # 50880-00-20-10
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Item # 50880-00-80-00
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Itme # 50880-00-20-00
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Item # 50880-00-40-00
The sub-miniature Series 50 regulator provides regulation of air pressure from 0 to 115 PSI. Available in both relieving and non-relieving versions, the unit’s size and shape makes it ideally suited for mounting in dental, medical and laboratory equipment where close regulation and fine adjustments are necessary.
The regulator is supplied with a panel nut for mounting in a 1/2 inch diameter hole. It can be screw driver adjusted, and set with a locking nut, or with the use of a control knob can be continuously adjusted. Ports (2) have 10-32 (M5) threads and are 180? apart on the side of the regulator body. The housing is nickel plated brass.
Several adjustment ranges are available for close regulation in most applications. Special designs are available.
Recently Viewed
Item # LPM16-10
These pneumatic totalizers can be used as an event, part or lot counter. The counter registers pneumatic impulses on 4, 6 or 8 digit displays. Standard units operate with impulse pressures between 25 and 100 psi. Low pressure models operate between 7.5 and 30 psi. A variety of options include panel mounting with screws or mounting clips and surface mount with base or rear stud. The counters are available with or without manual reset.
Item # PMT1H3B2
The Type PMT timer is an adjustable precise time delay control device. The timer is available with an on delay (NC) logic output.
Timing operation is dependent upon the input of a separate control signal which starts the timing sequence by setting a vacuum within the timer. Using atmospheric pressure (independent of line pressure), the timer begins the preset timing cycle. At the end of the cycle an internal 3 way valve is switched providing an output. The timer resets automatically after removal of the control signal.
The PMT has a separate subplate enabling the unit to be supplied with 10-32 or 1/8 NPT porting. The timer can be panel mounted with a bezel, or in the rear on a sub plate.
Item # 51012-01US
The Series 51 timer is an adjustable precise time delay control device. The timer is available with either an on delay- (NC) or off delay- (NO) 3 way built-in valve. It is designed for mounting along with valves or other logic devices and is available with 10-32 (M5) bottom ports, or 1/8″ NPT side ports. Bottom ported timers can also be panel mounted using (2) threaded M3 inserts on the top cover.
Timing operation can be set up in 2 ways; either via direct connection of the pressure line to be timed (1/8″ NPT ported only) or via a separate pilot signal. When pressure is applied to the input (or pilot port) the timing sequence begins by setting a vacuum within the timer. Using atmospheric pressure (independent of line pressure), the timer begins the preset timing cycle. At the end of the cycle an internal 3 way valve is switched providing an output. The timer resets automatically after removal of the control signal.
Item # 75027-94-00
Solenoid operated, air piloted poppet valves are available in single, double, priority and external air pilot supply versions. Priority version overrides signal from opposite solenoid to assure return to valve home position. Valves with external air pilot connections are used when switching pressures below 35 PSI.
Poppet valves usually provide higher flow rates than other types of valves because of flow path design.
Valves include a red manual override for easy testing. Encapsulated coils provide splash proof protection when used with plug connectors. Valves can be mounted individually using through body holes or assembled on manifolds.
Operating pressure range is 35 to 145 PSI. (Use valves with external pilot for switching lower pressures).
Through body holes are 3/16″ for 1/8 and 1/4 ported valves, 1/4 ? for 1/2 ported valves.
For valve specifications see appendix. See accessory section for connectors and manifolds. For detail dimensions contact factory.
Item # 76440-02-02
Two sizes of manifold kits are available (1/8 and 1/4 ported) for standard directional control valves, pneumatically or electrically operated (4 way, In-Line type, 2 or 3 position, except valve types 76123, 76124, 76127). Manifolds are single piece aluminum bases with common supply and exhaust ports on each end (1/8 or 1/4 metric respectively). For NPT supply ports, order supply line adaptor kit separately. Manifold kits include all valve mounting hardware, which accommodates both NPT, or Metric ported versions of valves. A hollow bolt is used to connect the valve to the base and supply the line air pressure. Two brass sleeves, sealed with O-rings, connect the exhaust ports. If a valve station is unoccupied (for future use), a blanking bar kit must be used to block manifold ports. Manifolds can be fastened down by 4 threaded M5 holes. Two or more 1/8 ported manifolds can be linked together with the use of connecting nipples and threaded tie rods (up to 3/16″ dia.) using the through body holes on the sides of the manifold to increase the number of stations.
There are no reviews yet.