Flow Full Open | 3.85 CFM at 100 psi 1.65 CFM at 45 psi |
Length | 9/16 in. |
Hex | 1/4 in. |
Thread | M5 |
Materials | Brass |
Item # 47200
Price Summary
- $29.59
- $29.59
- $29.59
For direct mounting on exhaust ports. Adjustable, equipped with locking nut to prevent tampering or loosening after setting is made.
Weight | 0.62 lbs |
---|
Be the first to review “Item # 47200” Cancel reply
You must be logged in to post a review.
Related Products
Item # 47090
For direct mounting on cylinder or valve ports, with L-banjo type instant push-in fitting and captive adjusting screw.
Item # 47071
For direct mounting on valve or cylinder ports, with captive adjusting screw and L-banjo type barb fitting.
Item # 47080
For direct mounting on cylinder or valve ports, with L-banjo type instant push-in fitting and captive adjusting screw.
Item # 47085
For direct mounting on valve or cylinder ports, with captive adjusting screw and L-banjo type barb fitting.
Item # 47091
For direct mounting on cylinder or valve ports, with L-banjo type instant push-in fitting and captive adjusting screw.
Item # 47086
For direct mounting on cylinder or valve ports, with L-banjo type instant push-in fitting and captive adjusting screw.
Item # 47070
For direct mounting on valve or cylinder ports, with captive adjusting screw and L-banjo type barb fitting.
Item # 47081
For direct mounting on valve or cylinder ports, with captive adjusting screw and L-banjo type barb fitting.
Recently Viewed
Item # 76440-02-04
Two sizes of manifold kits are available (1/8 and 1/4 ported) for standard directional control valves, pneumatically or electrically operated (4 way, In-Line type, 2 or 3 position, except valve types 76123, 76124, 76127). Manifolds are single piece aluminum bases with common supply and exhaust ports on each end (1/8 or 1/4 metric respectively). For NPT supply ports, order supply line adaptor kit separately. Manifold kits include all valve mounting hardware, which accommodates both NPT, or Metric ported versions of valves. A hollow bolt is used to connect the valve to the base and supply the line air pressure. Two brass sleeves, sealed with O-rings, connect the exhaust ports. If a valve station is unoccupied (for future use), a blanking bar kit must be used to block manifold ports. Manifolds can be fastened down by 4 threaded M5 holes. Two or more 1/8 ported manifolds can be linked together with the use of connecting nipples and threaded tie rods (up to 3/16″ dia.) using the through body holes on the sides of the manifold to increase the number of stations.
Item # 75046-11-00
Three way poppet design valves are solenoid operated, air pilot assisted. Valves include a red manual override lever for easy testing of pneumatic circuits. Coils are encapsulated for long life. Available in standard versions, or with a port for external air supply used for switching pressures below 35 PSI.
Operating pressure range is 35 to 145 PSI. (Use valves with external pilot for switching lower pressures).
For 2-way operation plug exhaust port 3. Through body mounting holes are 3/16″ for 1/8 and 1/4 ported valves, 1/4″ for 1/2 ported valves.
For valve specifications see appendix. See accessory section for electrical connectors. For detail dimensions contact factory.
Item # PMT1H2B3
The Type PMT timer is an adjustable precise time delay control device. The timer is available with an on delay (NC) logic output.
Timing operation is dependent upon the input of a separate control signal which starts the timing sequence by setting a vacuum within the timer. Using atmospheric pressure (independent of line pressure), the timer begins the preset timing cycle. At the end of the cycle an internal 3 way valve is switched providing an output. The timer resets automatically after removal of the control signal.
The PMT has a separate subplate enabling the unit to be supplied with 10-32 or 1/8 NPT porting. The timer can be panel mounted with a bezel, or in the rear on a sub plate.
Item # 75067-81-47
Pneumatically operated poppet valves are available in single, double or with priority port actuators. The priority port design overrides the signal from the opposite pilot operator to insure return to home position. Poppet valves rely on O rings and gaskets to seal passage ways within the valve and generally offer higher flow rates than other types of valves.
These valves are available in port sizes of 1/8, 1/4 and 1/2. Pilot ports are 1/8 for all size valves and require minimum of 35 PSI operating pressure. Single air pilot valves have an air supported spring return and require a pilot pressure equal to or greater than the air supply pressure at port 1. Valves can be mounted using through body holes or assembled on manifolds.
Pilot port size (for actuation): 1/8 for all size valves.
Operating pressure range 35 to 145 PSI. Actuation force (pilot pressure): 35 PSI minimum.
Mounting via 4 through body holes 3/16? Dia. (1/2? ported valves- 1/4? Dia.).
For valve specifications see appendix. See accessory section for manifolds if required. For detail dimensions contact factory.
Item # 50036
Brass metric sized fittings provide a full family of connectors for most applications in miniature pneumatics. Machined from solid brass stock, fittings are dependable, easy to install and reduce space requirements.
Series 50 fittings also include quick connect couplings and brass manifolds.
There are no reviews yet.